perfSONAR User Q&A and Other Discussion

[HADJALI Mehdi <>]

Hi Szymon,

 

I think it’s ok for Throughput test but not for OWAMP Test. I don’t find any solution for OWAMP Test.

 

The result of this threshold is based on millisecond result or a percentage ? Thanks in advance

 

Mehdi

 

Cordialement / Regards

Mehdi HADJALI

DSI Network & Telecom

Sopra Steria

Tour Chantecoq
5, rue Chantecoq

92800 Puteaux Cedex - France
Phone: +33 (0)1 47 17 23 04
- www.soprasteria.com

 

De : HADJALI Mehdi
Envoyé : jeudi 18 juin 2020 08:26
À : Szymon Trocha <>;
Cc : Phil Reese <>
Objet : RE: [perfsonar-user] Change scale graphs in Maddash-graphs

 

Hi Szymon,

 

I change this commands :

 

command: "/usr/lib64/nagios/plugins/check_owdelay.pl -u %maUrl -w .0002 -c .0005 -r 900 -l -p -s %col -d %row"

 

command:  "/usr/lib64/nagios/plugins/check_throughput.pl -u %maUrl -w .01 -c .005 -r 86400 -s %col -d %row"

 

Do these values correspond to what I want to apply?

 

I’m not sure because when I apply a new check, I didn’t see any changes.

 

Thanks in advance

Cordialement / Regards

Mehdi HADJALI

DSI Network & Telecom

Sopra Steria

Tour Chantecoq
5, rue Chantecoq

92800 Puteaux Cedex - France
Phone: +33 (0)1 47 17 23 04
- www.soprasteria.com

 

De : Szymon Trocha <>
Envoyé : mercredi 17 juin 2020 16:57
À :
Cc : HADJALI Mehdi <>
Objet : Re: [perfsonar-user] Change scale graphs in Maddash-graphs

 

W dniu 17.06.2020 o 16:25, HADJALI Mehdi pisze:

Hello,

 

I would like to change the scale of Owamp test and Throughput test like this :

 

For OWAMP Tests results :

statusLabels:

            ok: "Loss is 0”

            warning: “Loss is greater than 0.200”

            critical: "Loss is greater than 0,500"

            unknown: "Unable to retrieve data"

            notrun: "Check has not yet run"

 

For Throughput Tests results :

statusLabels:

            ok: "Throughput >= 10Mbps"

            warning: "Throughput < 10Mbps"

            critical: “Throughput < 5Mbps”

            unknown: "Unable to retrieve data"

            notrun: "Check has not yet run"

 

It’s possible to change this scale or not possible? Thanks in advance

 

Hi Mehdi,

In your maddash.yaml look for lines per each host in the matrix containing:
/usr/lib64/nagios/plugins/check_throughput.pl -u %maUrl ...

/usr/lib64/nagios/plugins/check_loss.pl -u %maUrl ...

These are Nagios checks and they should contain options "-c" and "-w" with some default values. "-w" is the threshold for Warning and "-c" for Critical. When changing keep them consistent through all nodes.

Then you may also want to match the labels in statusLabels sections as you mention above

Regards,

--

Szymon Trocha
Poznań Supercomputing & Networking Center

General NOC phone +48 61-858-2015 | noc.pcss.pl
Personal desk phone +48 61-858-2022

Wysłaliśmy do Ciebie ten e-mail w odpowiedzi na Twoje zapytanie lub w związku z oferowaną usługą. Przesłanie korespondencji do Centrum Zarządzania PCSS lub zgłoszenie telefoniczne jest równoznaczne z wyrażeniem zgody na przetwarzanie danych osobowych przez Instytut Chemii Bioorganicznej Polskiej Akademii Nauk w Poznaniu adres: ul. Z. Noskowskiego 12/14, 61-704 Poznań. Szczegółowe informacje znajdują się w naszej Polityce prywatności. | This message has been sent as a part of communication with PSNC NOC or your service request sent to us. For more information read our Privacy Policy.