perfsonar-user - Re: [perfsonar-user] Toolkit not recognizing NIC
Subject: perfSONAR User Q&A and Other Discussion
List archive
- From: Szymon Trocha <>
- To:
- Cc:
- Subject: Re: [perfsonar-user] Toolkit not recognizing NIC
- Date: Fri, 21 Sep 2018 10:06:07 +0200
- Ironport-phdr: 9a23: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
- Organization: PCSS
W dniu 20.09.2018 o 17:58,
pisze:
Hi All, We just set up a new system with the toolkit ISO. The 10G interface doesn't show up in the toolkit, only in the OS. System details: i7, 4GB RAM, intel x520DA2 card with 10Gb Cisco SR transceivers. p1p2 is connected to our router. Only em1 and LO show up in the toolkit for interfaces. ifconfig shows - I replaced the actual IPs with xx: em1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 128.198.xx.xx netmask 255.255.252.0 broadcast 128.198.xx.255 inet6 fe80::5ef9:ddff:fe78:270a prefixlen 64 scopeid 0x20<link> ether 5c:f9:dd:78:27:0a txqueuelen 10000 (Ethernet) RX packets 526962 bytes 39667668 (37.8 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 13203 bytes 4572503 (4.3 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 20 memory 0xe1a00000-e1a20000 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 70932 bytes 34610796 (33.0 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 70932 bytes 34610796 (33.0 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 p1p2: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 inet 128.198.xx.xx netmask 255.255.255.240 broadcast 128.198.xx.xx inet6 fe80::14cf:4f58:577f:bf90 prefixlen 64 scopeid 0x20<link> ether 00:1b:21:55:1e:c5 txqueuelen 10000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 Hi Greg, Is (was) the p1p2 interface you are looking for up and running on
your host? So looking at "ip addr show p1p2" result? If it's down
bring it up and verify again. regards, --
|
- [perfsonar-user] Toolkit not recognizing NIC, greg.williams, 09/20/2018
- Re: [perfsonar-user] Toolkit not recognizing NIC, Szymon Trocha, 09/20/2018
- RE: [perfsonar-user] Toolkit not recognizing NIC, Greg Williams, 09/20/2018
- Re: [perfsonar-user] Toolkit not recognizing NIC, Szymon Trocha, 09/21/2018
- Re: [perfsonar-user] Toolkit not recognizing NIC, Szymon Trocha, 09/20/2018
Archive powered by MHonArc 2.6.19.