Skip to Content.
Sympa Menu

perfsonar-user - [perfsonar-user] Throughput test via Toolkit

Subject: perfSONAR User Q&A and Other Discussion

List archive

[perfsonar-user] Throughput test via Toolkit


Chronological Thread 
    < Chronological >      < Thread >
  • From: Ignacio Peluaga Lozada <>
  • To: "" <>
  • Subject: [perfsonar-user] Throughput test via Toolkit
  • Date: Wed, 27 Jan 2021 11:46:37 +0000
  • Arc-authentication-results: i=1; mx.microsoft.com 1; spf=pass (sender ip is 188.184.36.50) smtp.rcpttodomain=internet2.edu smtp.mailfrom=cern.ch; dmarc=bestguesspass action=none header.from=cern.ch; dkim=none (message not signed); arc=none
  • Arc-message-signature: i=1; a=rsa-sha256; c=relaxed/relaxed; d=microsoft.com; s=arcselector9901; h=From:Date:Subject:Message-ID:Content-Type:MIME-Version:X-MS-Exchange-SenderADCheck; bh=B5QmQWf+H7lr4L69GWyvSV5JtojrTixrKaZVTDPoVdo=; b=U1GqieIKvyGwhtHQwcoTxEgmpt+d2+8ovbMfzXPMFpPQSPQUjE2WxZ4FocS5zZpnvtuL7ueZef/Ctv5nXCRF3XKHNIwbfYC5bhAah/mBX/e3f3YcMu/AP3jvwrkdnaZqyKCtZsD7YtyGhkNVHcVVgKj9sDJDHjieBpqTXrCvT7MY/gvwIhMIVzOZCyDpozR1teoCh1FCXY32FW89y4TnJPTdXlxS/wtzmYRwhrsnZ6yqK5BFGDtsRco+goOPYE7oFA1VRB0uhLSWL751QZjSJDn1ls+8rNkXxxYolpYYL+aAhn30U9C7V4+M4pZhORXLTkzoJYxfZx7YzDBDz/k4vQ==
  • Arc-seal: i=1; a=rsa-sha256; s=arcselector9901; d=microsoft.com; cv=none; b=k7MO99jR01bZlrCxLFcvGN9ejngyGqR67/pDeoR5rEGHM5GjQYnvay3/MNOXjWnmwKKOol0RPoVmA0tTEnXYxyGsf7GUa2PMZ0RfRN6qGcHDh4skZKWWB1dFYd+N4z+bHu7bU+JM8kn7anfkpWFBzD/22uCiOAxQFfquwnkhk2ce7cwXA3dtf/vuehyb7tJ60L/qOZmwCyBSezucDRNnhcVVePcZWyI0ZaosqvZIAMX4jW+T5UlFANND9wBBrsElGoYlQFV7LxaLx4Ori2nfB8UJAXpPYWg8YprAClOQCvZjVqV3+vMTu9z9vofd1s8aarizUc/mBbZG2yC3nBVzwA==
Hello all,

I have a question regarding scheduling throughput measurements between two
hosts, A and B, using the toolkit. Host B is behind NAT, host A is not.

Via host A's toolkit I have scheduled a throughput test to host B, but no
results are reported.

Therefore I ssh'd into host A and run 'pscheduler monitor' and saw there
indeed the throughput task as 'Failed'. I run the command there shown and it
fails (I get 'Run did not complete: Failed'), however if I remove all the
options except '--dest' it works.

So my question is, is there anyway to avoid having the toolkit set those
options (source, source-node, dest-node, etc)?

Thanks.

Regards,
Ignacio

Archive powered by MHonArc 2.6.24.

Top of Page