perfSONAR User Q&A and Other Discussion

["Garnizov, Ivan (RRZE)" <>]

Hi Rong,

 

The web_admin.log is a very high level log for the web interface of the toolkit.

In order to give us a better picture of the current case, could you please restart:

-          sudo service bwctl-server restart

-          sudo service owamp-server restart

-          sudo service cassandra restart

 

and  provide us the messages from the commands above and excerpts of a little while before the restart from:

-          /var/log/messages

-          /var/log/perfsonar/owamp_bwctl.log

-          /var/log/esmond/esmond.log

-          /var/log/cassandra/cassandra.log

 

Please tell how did you get to this state? Is that a new install or an upgrade? What in your understanding led to this state of the toolkit?

 

Please note the above commands are not sufficient to restore the full operation of the toolkit.

 

Regards,

Ivan

 

From: [mailto:] On Behalf Of Yao,Rong
Sent: Freitag, 10. Juni 2016 23:23
To:
Cc: Moye,Roger V; Adams,Andrew M; William J Allen
Subject: [perfsonar-user] perfS0NAR Services not running

 

Greetings, 

 

Services bwctl, regular_test, owamp and esmond in the perfSONAR shown on web interface are “Not Running”.  Please see the attached screen shot.

I looked at web_admin.log and saw those error messages:

 

2016/06/10 15:39:55 (31270) ERROR> BWCTL.pm:646 perfSONAR_PS::NPToolkit::Config::BWCTL::get_port_range - No port range for peer_ports

2016/06/10 15:39:55 (31270) ERROR> BWCTL.pm:646 perfSONAR_PS::NPToolkit::Config::BWCTL::get_port_range - No port range for iperf_ports

2016/06/10 15:39:55 (31270) ERROR> BWCTL.pm:646 perfSONAR_PS::NPToolkit::Config::BWCTL::get_port_range - No port range for iperf3_ports

2016/06/10 15:39:55 (31270) ERROR> BWCTL.pm:646 perfSONAR_PS::NPToolkit::Config::BWCTL::get_port_range - No port range for nuttcp_ports

2016/06/10 15:39:55 (31270) ERROR> BWCTL.pm:646 perfSONAR_PS::NPToolkit::Config::BWCTL::get_port_range - No port range for thrulay_ports

2016/06/10 15:39:55 (31270) ERROR> BWCTL.pm:646 perfSONAR_PS::NPToolkit::Config::BWCTL::get_port_range - No port range for owamp_ports

2016/06/10 15:39:55 (31270) ERROR> BWCTL.pm:646 perfSONAR_PS::NPToolkit::Config::BWCTL::get_port_range - No port range for test_ports

…

2016/06/10 15:39:57 (31269) ERROR> Host.pm:342 perfSONAR_PS::NPToolkit::DataService::Host::get_details - Unable to find host record in LS using hostname r1prpps01.mdanderson.edu

I do see those values are defined in the /etc/bwctl-server/bwctl-server.conf

# bwctl control channel

peer_port       6001-6200

# bwctl measurement test ports

test_port       5001-5900

Can anyone please advise what’s wrong here? 

Thanks,

Rong

------------------------

Rong Yao

Research IS & Technology Services

University of Texas MD Anderson Cancer Center

Email: | Tel: (713) 563-2687

The information contained in this e-mail message may be privileged, confidential, and/or protected from disclosure. This e-mail message may contain protected health information (PHI); dissemination of PHI should comply with applicable federal and state laws. If you are not the intended recipient, or an authorized representative of the intended recipient, any further review, disclosure, use, dissemination, distribution, or copying of this message or any attachment (or the information contained therein) is strictly prohibited. If you think that you have received this e-mail message in error, please notify the sender by return e-mail and delete all references to it and its contents from your systems.