perfsonar-dev - Translation from Cisco commands to Juniper [Was: Re: Looking glass command]
Subject: perfsonar development work
List archive
- From: Nicolas Simar <>
- To: GN-JRA1-list <>, "" <>
- Subject: Translation from Cisco commands to Juniper [Was: Re: Looking glass command]
- Date: Tue, 19 Dec 2006 16:32:43 +0000
Hi,
Chris has compiles a list of command that should be provided by the networks in order to help the NOC and PERT in their daily work. The command listed are cisco commands.
If you are using juniper (or any other equipment), could you please translate the following command (or even a subset of them) to Juniper commands as they will most likely be required for the prototype.
We are looking in particular at the ones preceeded by "*".
Thank you very much in advance.
Nicolas
-------- Original Message --------
Subject: Re: Looking glass command
Date: Tue, 19 Dec 2006 16:53:23 +0100
From: Chris Welti
<>
To: Nicolas Simar
<>
CC: Simon Leinen
<>
References: <> <> <>
Hi Nicolas,
I went over some available looking glasses (most items from GRNET) and added some functionality from brainstorming with my NOC/PERT colleagues.
Note, we only use Cisco devices, so I don't know if similar commands are available for other platforms...
Useful CISCO commands for PERT/NOC debugging (in GN2 JRA1):
General/IPv4:
show environment
*show interface <interface>
*show interface description
show ip access-lists
*show ip bgp <ip address>
show ip bgp summary
show ip bgp dampening dampened-paths
show ip bgp neighbor <ip address> advertised-routes
show ip bgp neighbor <ip address> received-routes
show ip bgp dampening flap-statistics
show ip interface <interface>
show ip mbgp <ip address>
show ip mroute <ip address>
show ip msdp sa-cache <as number>
show ip msdp sum
show ip msdp count
show ip msdp peer <ip address>
show ip ospf database external <ip address>
show ip protocols
*show ip route <ip address>
show ip rpf
show ip sdr
show ip sdr detail
show module
*show running interface <interface>
show version
*ping <ip address>
*trace <ip address>
mtrace <ip address>
IPv6:
*show ipv6 route <ipv6 address>
*show ipv6 interface <interface>
show ipv6 access-list
*show bgp ipv6 <IPv6 prefix network/length>
show bgp ipv6 summary
show bgp ipv6 flap-statistics
*ping ipv6 <ipv6 address>
*trace ipv6 <ipv6 address>
MPLS:
show mpls l2transport vc
*show mpls l2transport vc detail
show mpls forwarding-table <interface>
show ip vrf
show ip vrf detail
*show ip route vrf <VPN name>
*ping vrf <VPN name> <ip address>
*trace vrf <VPN name> <ip address>
(*) development priority; of course, all commands are important, but those are the ones which I'd say MUST be there.
Regards,
Chris
Nicolas Simar wrote:
Chris Welti wrote:
Hi Nicolas,
Our offices are closed from this Saturday till January 4th, so i'll
try to come up with some examples this week.
If I understand correctly, this is for commands to use on a router right?
Like interface descriptions, stats (counters), configuration etc?
Typically, at this stage, we are looking at show command like you can
find on typical looking glass e.g.
http://www.garr.it/mappagarr/garr-b-mapaltri-engl.shtml
If you think that you'll need quite a few of them, could you please
prioritise them (either on an individual basis or per group).
Thanks a lot.
Cheers,
Nicolas
PS: for clarification, by stats, I can see two type of things: show
command which shows counters values and the second one would be OID
access. The second one is not yet part of our portfolio, so you can
ignore it for the time being.
Regards,
Chris
Nicolas Simar wrote:
Hi Chris,
could I ask you to send a list the looking glass command that would be
useful for the NOC and for the PERT when troubleshooting problems. This
would be a helpful start for the Pilot. Could you please send this list
if possible before the Cambridge meeting.
Thanks a lot.
Cheers,
--
Nicolas
______________________________________________________________________
Nicolas Simar
Network Engineer
DANTE - www.dante.net
Tel - BE: +32 (0) 4 366 93 49
Tel - UK: +44 (0)1223 371 300
Mobile: +44 (0) 7740 176 883
City House, 126-130 Hills Road
Cambridge CB2 1PQ
UK
_____________________________________________________________________
- Translation from Cisco commands to Juniper [Was: Re: Looking glass command], Nicolas Simar, 12/19/2006
- RE: [pS-dev] Translation from Cisco commands to Juniper [Was: Re: Looking glass command], Luis Marta, 12/19/2006
Archive powered by MHonArc 2.6.16.